Showing posts with label Lcd Repair. Show all posts
Showing posts with label Lcd Repair. Show all posts

Sunday, May 15, 2011

Understanding Inverter Board

0 comments

Myads

Understanding Inverter Board
lcd monitor repair preview
For a newer LCD Monitor design, the inverter board is joining together
with the power board as shown in the above photo. Older LCD Monitor
has the inverter board separated from the power board as shown below
lcd-monitor-repair-preview-02

There are four types of inverter designs (topologies) used in the LCD
Monitors.
1) Buck Royer inverter
2) Push pull inverter (Direct Drive)
3) Half bridge inverter and (Direct Drive)
4) Full bridge inverter (Direct Drive)
Number 2, 3 and 4 are called Direct Drive because it eliminates the need
for the inductor (buck choke) and resonant capacitors found in a
conventional Royer Oscillator. In other words, Direct Drive architecture
reduces component count, lower production cost and most importantly
improved transformer designs that optimize performance.
1) Buck Royer Inverter
lcd-monitor-repair-preview-03
Block diagram of Buck Royer inverter
lcd-monitor-repair-preview-04
lcd-monitor-repair-preview-05

More Post:

How to repair your PSP's LCD Screen

0 comments

Myads

First of a to get all those screws out.  At first glance, you might think there are only 5 screws.  And for some reason, people who do instructionals on this subject on YouTube say there are 5 screws, and then the hidden one.  Okay, I’m shooting you straight.  There are 6 screws on this thing, and you have to peel back the “Do not open or your sh$t is voided” sticker in the battery compartment to find the last one.  It’s not hidden, there are no booby traps, and info on some missing mobster isn’t hidden in there.  It’s simply a screw with a warning label over the top letting you know that you are about to void your warranty.  Let's face it... if your PSP were still under warranty, would be we doing this repair ourselves? (Un)screw it.
 
 
find all of the screws so you can take off the case
There are two screws located in the upper battery compartment as well, two on the back of the console near the Memory Stick compartment, and one on the bottom in the dead center.  Take them all out and then come back to me.   Got them all out?  Good.  Now let’s pry that faceplate off and set it to the side.  Start at the bottom and slowly pull it up, it should come off pretty easily.  Once you have that off, you can get to work on taking the LCD out.  Some people think it’s necessary to remove the L and R buttons from the top.  It’s not.  Ignore them and try not to scuff them up with a screwdriver.


revealing the creamy goodness 
Assuming the PSP is facing you in the proper orientation, with the L/R buttons at the top, you’ll see that the metal plate containing the menu buttons at the bottom crosses right in front of the LCD panel.  To remove this, you simply take a small flat-head screwdriver remove it at the lower left hand corner.  Slide the screwdriver under the menu plate and pop it off gently.  This won’t take much pressure at all.  Try not to disconnect the wire ribbon that is attached at the other end.

The LCD and its ribbon cables
Once this is moved to the side, it’s time to remove your LCD.  See how easy it is to get to this point?  Take your tiny flat-head once again and go to the upper left corner of the LCD.  You’ll see there is a peice of raised metal on the LCD’s frame holding in the compartment.  Slide your screwdriver in here and slowly move the LCD up and out until it is no longer held down.  Do the same with the one at the lower left corner.  Now you should be able to just grab the screen with your fingertips and remove it.  Be careful once again with the wire ribbons that are attached.

 
pull up the LCD and disconnect its ribbon cables
You will see that there are two ribbons that connect to the PSP’s motherboard.  A large one and a small one.  The large once can be removed by simply popping the black connector up and away from you, then sliding the ribbon out.  The small one is reversed.  Grab the black snap with your fingernail and pull it up and toward you, then slide this ribbon out as well.  Congratulations, you just removed the broken LCD panel and are halfway home.
Okay, grab your new LCD panel.  They typically come with a blue film over them and a sticker underneath this to protect the screen.  Remove the blue film, but not the sticker.  We need to make sure we don’t scuff or scratch the screen during the installation.  Also, fingerprints are a pain in the ass when they require you to dismantle the system to wipe them off.

peel off the protective film from your new LCD
Okay, take the ribbons and slide them in the way the old ones came out.  Pay close attention to make sure they are pushed in all the way.  If they are not far enough in your screen won’t work.  Now close down the black tabs and get ready to put your screen in its cradle.  Start with the right side, sliding it into place, then the left side.  Once this is snapped in, you can replace the menu plate that you took off.  It snaps in just as easy as it came off.  The only thing left is to replace the faceplate and put all those screws in.  Remember, the longer silver screw goes on the outside at the bottom of the PSP, the shorter silver screw goes next to the black one in the battery compartment.  The black screws are pretty much all interchangeable.

good as new! Let's play some homebrew games!
Okay, everything is back together once more.  Power up your PSP.  If your screen works, then congrats to you.  You just repaired your broken PSP and didn’t even break a sweat.  Or your wallet.  Sorry greedy PSP techs.  And that concludes today’s lesson.  Tomorrow I will show you how you can derive solar power from a sun-baked pile of dog feces.


Source: http://www.ocmodshop.com/ocmodshop.aspx?a=1533&p=3925

More Post:

A Bad Capacitor

0 comments

Myads

You cannot be assured that just looking at a capacitor will tell you if it is bad or not. Capacitors can *definitely* go bad and show no visual signs of it. Capacitors can fuse inside or slowly leak power, and still look fine.
My advice is if an LCD isn't working, just try replacing ALL the electrolytic capacitors on the power board with ones of the same microfarad rating and equal or higher voltage.
The voltage rating determines how many volts the capacitor can *handle* in terms of input, not how much it outputs! So it's fine to go over because whatever the capacitor is powering will draw however many volts it needs from the capacitor, so a higher voltage rating actually helps make the capacitor last longer.
However, if the voltage rating is far higher than the rating of the capacitor you are replacing, it can get really hot from holding too much charge, and might melt other components on the circuit board. Electronics are designed to get only so hot. Moreover, it may not fit on the board! So make sure you bring the board in to your Radio Shack and visually inspect the new capacitors to make sure they will fit. A good rule of thumb is not to exceed 2x the voltage rating of the capacitor you are replacing.

More Post:

Repair a Desktop LCD with Bad Capacitors

0 comments

Myads

How-To Repair a Desktop LCD with Bad Capacitors

Source: http://www.aplusperfect.com/articles/lcd_capacitor_repair


January 17, 2008 By Jeremy Brock
Desktop LCD monitors fail for a variety of reasons, the most common being bad electrolytic capacitors. If you are willing to invest the time you can fix your LCD for a few dollars in parts. For this demonstration I’m using an IBM ThinkVision 6636-AB1 however the same techniques apply to most desktop LCD Monitors.
Disclaimer:
A+ Perfect Computers, LLC, is not responsible for any damages to your device, person, or property. Computer, Laptop, or LCD disassembly and part installation is at your own risk. This Guide offers only suggestions for taking apart your device. The components inside your device are highly sensitive. Always ground yourself by using an ESD wrist strap or by touching a metal object while handling sensitive electronics.
    Symptoms:
  • No Picture on Screen
  • LCD displays picture briefly then turns off
    Tools:
  • Soldering Iron
  • Desoldering Station or Solder Sucker
  • Phillips Head Screw Driver
  • Spudger (Available Here and Here)


This LCD would turn on for a second then shut off. These symptoms are usually caused by a bad CCFL light or inverter board. After opening the LCD I did a visual inspection of the PCB looking for any dark areas, damaged IC’s or bad filter capacitors. The top of filter capacitors should be flat, bulging or leaking is an easy way to detect a failing capacitor. If available an ESR meter can be used to validate the capacitor is failing.
In this instance there are three bulging capacitors. Finding replacement LCD components can be tricky however replacement capacitors can be purchased at most electronic part stores. In this case we use mouser.com
To order capacitors enter the Capacitance and Voltage rating into the Capacitor Product Filter on Mouser. Look for the capacitor with the smallest diameter and length, prioritizing a smaller diameter over length if necessary.
Click on an image for a larger picture
Back of LCD Monitor
Remove the mount (not shown) and housing screws. The housing screws are usually located on corners of the LCD however they may be hidden under a rubber insert or sticker.
Open Housing LCD's use plastic clips or snaps to hold the housing together. Use a spudger to gently pry the housing apart. Avoid using a metal screw driver as it will damage the plastic.
Remove Protective Cover Remove the protective cover. Depending on the design you may need to slide the protective cover off once the screws are removed.
Picture of Inverter Board On this model the inverter board and power supply are on the same board
1. LCD CCFL Backlight Connectors
2. LCD Ribbon
3. Analog to Digital Converter
4. Power Supply
5. Inverter Board
Bad Capacitors The top of an electrolytic capacitor should be flat. You can visually inspect capacitors by looking for a bulging top or dry brown crusty substance leaking from the capacitor.
Desolder Capacitors Electrolytic capacitors have a solid line or dash going down one side for negative polarity. Installing an Electrolytic capacitor backwards can damage it so make note of the polarity relative to the board then desolder it
compare capacitors Make note of the capacity and voltage, in this case the 1000uf 16V and 470uf 16V (not shown) capacitors were bad.
solder new capacitors Next solder the new capacitors in place making sure the polarity is correct. After soldering reassemble and test the monitor

More Post:

Wednesday, May 11, 2011

Laptop LCD Repair - A Photo Guide

0 comments

Myads

Laptop LCD Repair - A Photo Guide




If you're undertaking some laptop LCD repair, removing and replacing your screen means you are working with a very fragile and very expensive component.

Follow these steps carefully, the machine in the photos here is a Toshiba but the job is quite similar regardless of what brand machine you are working on.
Laptop LCD Repair



Laptop LCD Repair


Remove the mask stickers and then the screws from behind the stickers.


Laptop LCD Repair


Carefully pull away the mask assembly from around the screen.


Laptop LCD Repair



Laptop LCD Repair


Remove the LCD mounting screws behind the stickers and also behind the inverter cable.


Laptop LCD Repair


The LCD should now be free from its mountings.


Laptop LCD Repair


Disconnect the cable from the back of the LCD.

To complete your laptop LCD repair and fit your new screen, just reverse the steps above. 

More Post:

Circuits and components found in LCD TV's

0 comments

Myads

Learn to identify important circuits and components found in LCD TVs
Typical LCD TV power supply board
LCD TV Main Board

LCD TV controller/t-con board 
LCD TV inverter board

More Post:

Friday, March 18, 2011

LED Flashlight

0 comments

Myads

LED Flashlight

It is a small versatile.
Applies as a tool to illuminate the LCD screens in functional testing, illuminating the inside of cabinets CPU in camping, car, fishing, etc..

Features:
90mm long x 25 mm in diameter
Aluminum body with anodized treatment
Uses 3 AAA batteries (stick) 
9 LEDs 
Power button click type reve 
RSO


More Post:

Micro Controller LCD - Micon

0 comments

Myads

Micro Controller LCD - Micon

Chip SMD
Several models of LCD monitors from Samsung and AOC use the micro controller of the mark with the code NT68F63LG Novatek, which has made a considerable number of defects.

The classic symptom of this defect is when the monitor does not open the image and is riding a warning on the screen " Not Optimum Mode, Recommended Mode ... "followed by " 1024 X 768 60 Hz "for models 15" and " 1280 x 1024 75Hz "to 17".
Some monitors AOC is to maintain the image on the screen, but with a greenish tint.

Unfortunately you can not rewrite the EEPROM embedded in it, since the defect is internal communication. If Micon is nice, the EEPROM can be written and rewritten many times as necessary, including for any model that uses the infamous NT68F63LG.
But the exchange of Micon is required in virtually 100% of the defects of timing and communication.

We supply the chips already written to various models of Samsung and AOC:
Just remove the defective weld and the new 
.

More Post:

LCD REPAIR: The LCD screen does not light

0 comments

Myads


The LCD screen does not light



One of the most perplexing failures of LCDs, is when he turns on the power light turns green, as if normal, but the screen does not light and no image appears ...
Thus, at first glance, have no clue to the possible cause, because it can be everything.
A first step before starting to dismantle everything at random, at least, is to check if the motherboard is sending image. 
But as if nothing appears on the screen?
Well, we can not see it, but if it is being generated, be it '. To see it, we need to illuminate the screen, as they would fluorescents. 
At this time, comes into play a simple, powerful and small flashlight LEDs.
To reach a window behind the LCD screen, we need to do a partial disassembly of the device. 

So already with access to the back of the screen, turn on the monitor is already connected to a CPU, where an image is being generated and light up any window with his flashlight. 



Looking at the screen in front, we note the presence of the image.


By exclusion, we now know is that the possible cause or in lighting or source. Then proceed with the tests to detect the presence and balance of the MAT in the output of the inverters and verification of fluorescent lamps, to resolve the defect.
If, on the other hand, there really is no image, then the research question involves the motherboard monitor.



Are you interested in purchasing a flashlight Led? 
See more details about it by clicking here



More Post:

MONITOR REPAIR: LG did not leave the screen saver

0 comments

Myads

LG did not leave the screen saver




Q: In my workshop, and a sta monitor LG FLATRON W2043S model with the following default: normal league, when you put a sign makes the message POWER SAVING MODE.
I checked the source and everything ok. I noticed that this also happens with other models.
What might be the cause?


A: This means that the monitor is not detecting the sync signal from horizontal or vertical.
The cause may be a defect in the signal cable (check wiring on pins 13 and 14).
But if the circuit monitor, the cause should be near the Mykonos, a transistor or fusistor pifado line circuit horizontal or vertical. If not, it is the Micon.

More Post:

Followers

Archive

 

Cell Phone Repair. Copyright 2008 All Rights Reserved Revolution Two Church theme by Brian Gardner Converted into Blogger Template by Belajar Blog Bisnis Online